US / en
You supply the RotopaX Tank, we'll make hauling it even easier. Grab a SeaSucker RotopaX Tank Holder, powered by two 6" SeaSucker mounts, and easily attach your existing tank and hardware. Put your tanks on when you need them, remove in seconds when you don't! SeaSucker's RotopaX Tank Holder is compatible with any RotopaX tank up to three gallons. No matter what you're hauling, SeaSucker will make your next overlanding adventure easier.
RotopaX tank and hardware are not included.
Couldn't load pickup availability
SeaSucker's got you covered! Check out all of the latest releases to our innovative Overland & RV Accessory Collection.
- - Designed to hold any RotopaX tank up to 3 gallons.
- - It is recommended that you mount the RotopaX Tank Holder on a vertical surface (back glass on SUV, side window of van) with the mounts stacked vertically.
- Q: How strong are the vacuum mounts?
- A: “Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
- Q: How long do the vacuum mounts last before they lose power?
- A: There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
- Q: Do I need to clean the surface I’m going to attach my SeaSucker to?
- A: Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
- - Made to hold any RotopaX tank up to 3 lb.
- - Attaches to metal, glass or fiberglass surfaces.
- - 3/8" thick high-density polyethylene (HDPE) deck for strength and durability.
- - When mounted vertically: approx. 15" tall, 2.75" deep, 6.5" wide
- - Approx. 2.05 lb.
- - Powered by two 6" SeaSucker mounts.
Customer Reviews
- DPDaniel P.Verified Buyer1 week agoRated 5 out of 5 starsExcellent Product
It is an excellent product for your camping accessories with great quality and resistance.
- JJo.SVerified Buyer2 months agoRated 5 out of 5 starsOff-road and roadtrip essential
I have had this product on my car on and off for about 2000 miles. This includes highway driving, off-roading and rainy conditions, and never once did it leave me worried. One initial suction pump was enough for a full 2gal rotopax to stay put over 400+ miles! Nice to have on roadtrips and trail adventures so you can take a break to refuel, and can be removed with ease, compared to other rotopax mounts. Phenomenal product in every single aspect.
- GDGlen D.Verified Buyer3 months agoRated 5 out of 5 starsSimple solution that works great
Works perfectly, very happy with this product
- CBConrad B.Verified Buyer4 months agoRated 5 out of 5 starsInitial review
Well I have only had it mounted on the side of my Smartcap for 3 days and only on highway/street use, but it’s working like a charm on a 2 gallon rotopax. I’ve only had to give one of the suction cups one pump during this time !
- LHLevi H.Verified Buyer4 months agoRated 5 out of 5 starsRoto Pax says, you. :) Camp shower mount says I
I'd been looking for different ways to mount my camp shower without drilling holes in my camper walls. Social media kept dropping these SeaSucker ads in my feed. I explored all the different options that SeaSucker had, and saw the RotopaX mount looked to be my best option. It was a flat mounting surface, pre drilled holes and I said to myself, SELF: (and I knew it was me cause I recognized my voice) Lets try this one out and see how this pans out. Using a flat sturdy material I mounted everything for the camp shower to my board, then bolted the board to the SeaSucker. And it WORKS! Secures to the camper wall and holds my camp water heater in a convenience place for both my galley inside as well as my shower tent.
May not be what the designers had in mind, but it's working great for my needs.
Only thing I'd say could be better: the grip is a little narrow for fat fingers.
OFFICIAL PARTNER TO THE UCI & TEAM JUMBO VISMA
Innovation is the foundation of our company. Our founder, Chuck Casagrande, has invented well over 200 different products to date. Every year SeaSucker works to introduce more and more creative solutions for the athlete or angler on the go.
SeaSucker’s R&D team promise to continue to provide consumers with premium products centered on innovation.
READ MORE READ LESS
WATCH
WINNING TEAM
Don't Forget to Add Plugs to your Cart!
HUSKE 12x100mm Thru-Axle Plugs
HUSKE 15x100mm Thru-Axle Plugs
HUSKE 15x110mm Thru-Axle Plugs (Boost)
HUSKE 20x110mm Thru-Axle Plugs
HUSKE 20x100mm Thru-Axle Plugs
HUSKE 9x100mm Quick Release Plugs w/ QR Axle
HUSKE 9x100mm Quick Release Plugs - No Axle
It's time to select the right HUSKE Plugs to fit your bike. If you don’t know what front hub your bike has, it’s not that hard to figure out - all you have to do is measure it.
First, get a ruler or tape measure showing millimeters (sorry Americans, the bike world is firmly in the grip of METRIC TYRANNY!).
Step 1: measure the diameter of the hole at the end of your forks - it will be either 9mm, 12mm, 15mm or 20mm.
Step 2: measure the distance between the holes on your fork - it will be either 100mm or 110mm. Now purchase the HUSKE Plugs that match your measurements. There’s a color coded chart below that will help you make sure you’re buying the right set.
