US / en
We know a good thing when we see it, and we've seen the WaterPORT 4.0 Gallon Water Tank. Our WaterPORT x SeaSucker Tank Mount takes all the hassle out of mounting the tank on your vehicle. It attaches with three of our powerful 6" vacuum mounts, letting you put it where it's most needed, most accessible, or even most out of the way. And when you're back to the daily commute, it effortlessly removes to stow away until your next adventure.
Oh, and the WaterPORT 4.0 Gallon Water Tank? It lets you take pressurized water wherever you need it. 3.85 gallons of water available to you wherever you need to clean, rinse, refresh, or just water something down. Add pressure as you fill it with a standard garden hose, or use the optional Pump Cap to pump it up while on the road. You can even connect a bike pump, or air compressor to the included Schraeder valve to add up to 40psi. Better still, you can use the WaterPORT PumpCap; find it here.
Choose between Mount + Tank, or just the Mount.
Save $40 when you buy the full kit with Mount + Tank.
Couldn't load pickup availability
SeaSucker's got you covered! Check out all of the latest releases to our innovative Overland & RV Accessory Collection.
- Q: How strong are the vacuum mounts?
- A: “Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
- Q: How long do the vacuum mounts last before they lose power?
- A: There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
- Q: Do I need to clean the surface I’m going to attach my SeaSucker to?
- A: Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits
Customer Reviews
- MHMichael H.Verified Buyer4 months agoRated 5 out of 5 starsGenius Products
I've been a SeaSucker fan for a while and always appreciated the ingenuity that goes into their product line. Beginning years ago with a family members boat, I was happy to see the introduction of their RV/camp line up. Their kitchen (V1) is one of my favorite camping accessories and I was happy to see the WaterPort and mount combo. The mount lives on the back of my class B campervan and I love having water at the ready. The WaterPort stands on its own, and folks can check reviews there - but the tank mount is really overbuilt. This thing, even when filled, doesn't move or bounce at all on the van. The bottom shelf/plate doesn't seem to do anything as it makes almost no physical contact with the tank above - I tried flipping it too, wondering if that somehow makes a difference; alas, no. Just the same it doesn't seem necessary unless using it as a standalone shelf without the tank (which now that I think of it seems genius too)
Buying the set was a bit challenging, the mount shipped quick and arrived within a couple days; the tank however did not. It is apparently a drop-ship item from WaterPort directly and however SeaSucker and WaterPort have their order systems connected simply doesn't work. I had called a number of times and the voice mail says to send an email - so I would send an email and then get a call back shortly after from someone simply saying "we had a missed call"; email replies took days and when I finally got to someone they said it just takes "a few more…
- KKhalil2 months agoRated 5 out of 5 stars5 Stars
Amazing, and highly recommend them.
- FGFrancisco Gonzalez (.Verified Buyer2 months agoRated 3 out of 5 starsMixed feelings
It really seems like a good product. I installed it on my Bronco Sport back window and after a day or so it was loosing suction. The initial suction is great, holds strong but I wouldn’t use it as a permanent solution to carry my waterport tank. Probably is best for a temporary by-trip solution.
SSeaSucker2 months agoHi Francisco,
This is how the product is designed to function. It's a temporary solution for when you need it. Although we say the vacuum mounts will hold for at least 24 hours, they often hold vacuum for much longer.
- RSRobertrel S.Verified Buyer6 months agoRated 4 out of 5 starsWorks Well
This works really well, I was worried about it holding the weight but it did well. I couldn't place it where I wanted to for my camp kitchen but that was due to the curves on my Jeep and not an issue with this mount.
- CCalifornia6 months agoRated 5 out of 5 stars5 Stars
Amazing! This is what I've been looking for for so long time! Thank you guys!
FAQS
“Strong like bull.” 4.5” vacuum mounts have a rated pull strength of 120lbs, pulling straight out from center. Pull strength on a shear load, i.e. pulling from the side, will be less. 6” vacuum mounts are 210lbs rated. Obviously, putting multiple vacuum mounts on a single product multiplies the maximum holding power.
There’s no set time limit on our vacuum mounts. It depends in part on the surface you attach to, the condition of the vacuum mount, the load you put on it, and other factors. As for surfaces to attach to, vacuum mounts in general were designed to carry big sheets of glass and other solid surface materials, so smoother, flatter surfaces are ideal. Clean surfaces and clean SeaSuckers go a long way to maximizing the hold time. In any event, if the vacuum mount begins to lose some vacuum, it will warn you so you can get it back to full power before it comes off. The vacuum pump’s plunger will extend from the pump cylinder when it starts to lose power, revealing an orange indicator band. Once you see orange, that’s your cue to repump your SeaSucker. For car racks, the simplest thing to do is to check the rack before you get in your vehicle, and check it each time you stop for gas, food, or the bathroom.
Clean off any surface dirt from the mounting surface before attaching your SeaSucker. While you’re at it, make sure the sealing edge of the vacuum pad is clean too. You don’t have to clean the mounting surface with alcohol wipes, as one overly-enthusiastic customer told us they do, but a quick wipe with a wet paper towel or napkin wouldn’t hurt. Let us make it easy for you: get one of our Cleaning Kits.
No, the HDPE and the raw materials we use to manufacture our vacuum mounts all have a high-performance UV inhibitor built in. Your SeaSucker products should look good for years.
Where are SeaSucker products made?
SeaSucker products are proudly made in the USA. We go from raw materials to finished products all from our factory in Bradenton, Florida.
OFFICIAL PARTNER TO THE UCI & TEAM JUMBO VISMA
Innovation is the foundation of our company. Our founder, Chuck Casagrande, has invented well over 200 different products to date. Every year SeaSucker works to introduce more and more creative solutions for the athlete or angler on the go.
SeaSucker’s R&D team promise to continue to provide consumers with premium products centered on innovation.
READ MORE READ LESS
WATCH
WINNING TEAM
Don't Forget to Add Plugs to your Cart!
HUSKE 12x100mm Thru-Axle Plugs
HUSKE 15x100mm Thru-Axle Plugs
HUSKE 15x110mm Thru-Axle Plugs (Boost)
HUSKE 20x110mm Thru-Axle Plugs
HUSKE 20x100mm Thru-Axle Plugs
HUSKE 9x100mm Quick Release Plugs w/ QR Axle
HUSKE 9x100mm Quick Release Plugs - No Axle
HUSKE 5x100mm
HUSKE 12x110mm
It's time to select the right HUSKE Plugs to fit your bike. If you don’t know what front hub your bike has, it’s not that hard to figure out - all you have to do is measure it.
First, get a ruler or tape measure showing millimeters (sorry Americans, the bike world is firmly in the grip of METRIC TYRANNY!).
Step 1: measure the diameter of the hole at the end of your forks - it will be either 9mm, 12mm, 15mm or 20mm.
Step 2: measure the distance between the holes on your fork - it will be either 100mm or 110mm. Now purchase the HUSKE Plugs that match your measurements. There’s a color coded chart below that will help you make sure you’re buying the right set.
